Add documentation to control codes

From: Roberto E. Vargas Caballero <k0ga_AT_shike2.com>
Date: Thu, 27 Sep 2012 18:34:07 +0200

Add the documentation from the vt100 manual programmer:

Control Octal Action Taken
Character Code
-------------------------------------------
NUL 000 Ignored on input (not stored in input buffer;
                        see full duplex protocol).
ENQ 005 Transmit answerback message.
BEL 007 Sound bell tone from keyboard.
BS 010 Move the cursor to the left one character position,
                        unless it is at the left margin,
                        in which case no action occurs.
HT 011 Move the cursor to the next tab stop,
                        or to the right margin if no further tab stops
                        are present on the line.
LF 012 This code causes a line feed or
                        a new line operation. (See new line mode).
VT 013 Interpreted as LF.
FF 014 Interpreted as LF.
CR 015 Move cursor to the left margin on the current line.
SO 016 Invoke G1 character set, as designated by SCS
                        control sequence.
SI 017 Select G0 character set, as selected by ESC ( sequence.
XON 021 Causes terminal to resume transmission.
XOFF 023 Causes terminal to stop transmitted all codes
                        except XOFF and XON.
CAN 030 If sent during a control sequence, the sequence is
                        immediately terminated and not executed. It also causes
                        the error character to be displayed.
SUB 032 Interpreted as CAN.
ESC 033 Invokes a control sequence.
DEL 177 Ignored on input (not stored in input buffer).
--------------------------------------------
---
 st.c |   28 +++++++++++++++++++---------
 1 file changed, 19 insertions(+), 9 deletions(-)
diff --git a/st.c b/st.c
index 64e0aff..aa5f085 100644
--- a/st.c
+++ b/st.c
_AT_@ -1789,32 +1789,42 @@ tputc(char *c, int len) {
 		write(iofd, c, len);
 
 	switch(ascii) {
-	case '\t':
+	case '\t':	/* HT */
 		tputtab(1);
 		return;
-	case '\b':
+	case '\b':	/* BS */
 		tmoveto(term.c.x-1, term.c.y);
 		return;
-	case '\r':
+	case '\r':	/* CR */
 		tmoveto(0, term.c.y);
 		return;
-	case '\f':
-	case '\v':
-	case '\n':
+	case '\f':	/* LF */
+	case '\v':	/* VT */
+	case '\n':	/* LF */
 		/* go to first col if the mode is set */
 		tnewline(IS_SET(MODE_CRLF));
 		return;
-	case '\a':
+	case '\a':	/* BEL */
 		if(term.esc & ESC_STR)
 			break;
-
 		if(!(xw.state & WIN_FOCUSED))
 			xseturgency(1);
 		return;
-	case '\033':
+	case '\033':	/* ESC */
 		csireset();
 		term.esc = ESC_START;
 		return;
+	case '\016':	/* XXX: SO */
+	case '\017':	/* XXX: SI */
+	case '\032':	/* XXX: SUB */
+	case '\030':	/* XXX: CAN */
+	default:
+	/* case '\005':	ENQ (IGNORED) */
+	/* case '\000':	NUL (IGNORED) */
+	/* case '\021':	XON (IGNORED) */
+	/* case '\023':	XOFF (IGNORED) */
+	/* case 0177:	DEL (IGNORED) */
+		break;
 	}
 
 	if(term.esc & ESC_START) {
-- 
1.7.10.4
--yrj/dFKFPuw6o+aM
Content-Type: text/x-diff; charset=utf-8
Content-Disposition: attachment; filename="0002-Add-SUB-and-CAN-control-codes.patch"
Received on Mon Sep 17 2001 - 00:00:00 CEST

This archive was generated by hypermail 2.3.0 : Sat Oct 06 2012 - 19:36:02 CEST